Click Here

 

They are making several great pointers on the subject of How to Install a Bathtub in general in the article further down.

Mounting a bath tub isn't precisely rocket science, however it does need solid plumbing, carpentry, and also often, tiling skills. Changing an old bathtub with a new one is additionally a reasonably challenging task. If the old bathtub is conveniently accessible, the task can move rapidly; if you have to open a wall surface to get rid of the old tub as well as position the new bath tub, the task is much harder. In either case, the project is within a home handyman's skills, although you will certainly require a helper to leave the old tub as well as embeded in the brand-new one. Make certain you have certified yourself for the job and fit attempting it. Rather than working with a service provider to take over a halfway-completed job, it is far better to think about using one before you begin. Chances are you might need a specialist plumber to make tube links.
This post will certainly assist you install a brand-new bathtub in your washroom if you have already acquired a brand-new bathtub as well as do not need to alter the setup of your previous water supply pipelines.
Your tools and product list need to comprise the following:

 

• New Bath tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Knife


• Measuring tape


• Pipe Caps


 

Getting ready for the Setup

Firstly, the supporting structure provided with the bath needs to be fitted (if required) according to the maker's instructions. Next, fit the taps or mixer to the tub. When suitable the tap block, it is essential to make sure that if the faucet features a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bathroom, it is also sensible to fit a supporting plate under the taps device to prevent stress on the tub.
Fit the flexible tap ports to the bottom of the two faucets utilizing 2 nuts and olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet with the hole in the bathroom. Utilize the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make certain you utilize all of the provided washing machines.
Link the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath need to now be ready to be fitted in its last position.

 

 

Removing Old Touches

If you need to replace old faucets with new ones as a part of your installation, then the first thing you need to do is disconnect the water supply. After doing so, activate the taps to drain any type of water continuing to be in the system. The procedure of removing the existing faucets can be rather problematic due to the limited gain access to that is commonly the case.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the faucets. Have a towel ready for the remaining water that will certainly originate from the pipes. As soon as the supply pipes have actually been eliminated, utilize the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from turning throughout this process. When the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any type of old securing substance.
Before moving on to fit the brand-new taps, contrast the pipe links on the old taps to the new taps. If the old faucets are longer than the new taps, then a shank adapter is needed for the new faucets to fit.

 

 

Installing the Tub

Making use of the two wooden boards under its feet, place the bathtub in the required setting. The wooden boards are practical in equally spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto 4 small factors.
The following goal is to ensure that the tub is leveled all round. This can be attained by inspecting the spirit level as well as readjusting the feet on the tub till the level checks out degree.
To mount taps, fit the bottom of the outermost versatile tap connector to the suitable supply pipeline by making a compression sign up with; after that do the exact same for the various other faucet.
Activate the water supply and also examine all joints as well as brand-new pipework for leaks as well as tighten them if essential. Fill the tub and likewise inspect the overflow electrical outlet and the regular outlet for leakages.
Finally, take care of the bath paneling as explained in the manufacturer's instruction manual. Tiling and also sealing around the tub must wait up until the tub has been made use of at least when as this will settle it right into its last position.

 

 

Suitable New Taps

If the tails of the brand-new taps are plastic, after that you will need a plastic port to prevent damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end offers a link to the existing supply pipes.
If you require to fit a monobloc, then you will certainly require decreasing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, place the tap in the mounting hole in the bath/basin ensuring that the washers remain in area in between the faucet and the sink. Protect the faucet in position with the producer provided backnut. When the tap is safely in position, the supply pipes can be attached to the tails of the taps. The taps can either be linked by using corrugated copper piping or with regular faucet adapters. The previous type ought to be linked to the faucet ends initially, tightening just by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.

 

 

Tiling Around the Bathtub

In the location where the bath fulfills the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the installation can move sufficient to fracture a stiff seal, causing the water to permeate the wall surface in between the bath and the tiling, resulting in complications with moisture and possible leakages to the ceiling below.
You can select from a variety of coloured sealers to assimilate your fixtures and fittings. They are marketed in tubes and cartridges, and are capable of securing spaces up to a width of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to constantly fill the bath tub with water prior to securing, to allow for the movement experienced when the tub remains in use. The sealant can fracture relatively very early if you do not take into consideration this activity before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally quickly offered on the marketplace. It is advisable to fit the floor tiles using water-resistant or water resistant glue and also cement.

 

How to Install a Freestanding Bathtub?

 

Installing a freestanding bathtub or any kind of bathtub is not a difficult task if you have a sophisticated guide on installing a freestanding bathtub in your bathroom. Aside from getting the freestanding bathtub to your bathroom, you can do all the work without paying a plumber. A bathroom with a bathtub is a retreat where you can feel the sensation of coming home and soaking in that hot water. It is a great way to remove all the stress from your day.

This guide will walk you through installing a freestanding bathtub in simple steps and help you find relief.

 

Slope

 

Make sure your bathroom has a proper slope. If your floor lacks a slope, the water flow to the drain will not function, which leads to a blocked drain which can cost you money. You can use the level device to see your bathroom's vertical and horizontal aspects. Once you have that information, you must carry out the next step.

 

Placement

 

A freestanding bathtub has a unique characteristic that helps you bring elegance to your bathroom. A freestanding bathtub comes in various sizes and shapes suitable for different types of bathrooms.

According to the information you gathered from the level device, you must pick a bathtub that suits your style and fits your bathroom aesthetically. You can place a freestanding bathtub virtually anywhere, such as in the corner, near the wall, or even at the center of your bathroom. However, you must ensure proper plumbing where you want to install the tub. If not, then you must call a plumber.

 

Clean the bathroom floor

 

After deciding where to place the bathtub, you must clean the entire bathroom floor so that the dust and debris do not accumulate underneath the tub. Simple cleaning is enough, and you will clean it again after the installation.

 

Steps to Install a Freestanding Bathtub:

 

STEP 1: Place the protective blanket in the adjacent area where you want to install the bathtub. It will help you protect the bathtub's sides when you do the installation.

STEP 2: Now, place the 4x4 lumber in the area where you want to install the bathtub. Place the bathtub on top of the lumber, and align the drain line with the bathtub drain.

STEP 3: A freestanding bathtub comes with a drain kit. If not, make sure you purchase one with your bathtub. You can pop that drain kit and align it with your bathroom drain line. Ensure that you tighten the drain nut enough so there is no water leakage. You must also clean the bathtub’s drain to remove the factory dirt and debris.

STEP 4: Clean the drain hole in your bathroom. It helps to do the installation without any water blockage. A drain cleaner or bleach will suffice. Once the drain dries entirely, take a small amount of clear silicon and place it around the underside of the pipe flange.

STEP 5: Attach the drain tailpiece to the bottom of the bathtub. Place the rubber or plastic bushing with the plumbing material at the top of the tailpiece and screw the drain nut up the tube until it tightens both the bathtub’s drain and the drain tailpiece. Now you must add the lubricant to the seal to ensure there is no water leakage in the pipe connection.

STEP 6: Place caulk around the bottom edge of the bathtub. Take out the lumbar support and carefully bring the bathtub to the floor. Use a damp cloth to clean the excess caulk and debris and plumber putty to cover the tub drains and the floor.

 

Tips to Maintain a Freestanding Bathtub:

 

• Always look for the clog in the drain. You can pull it out with a small stick if hair or debris is in the gutter.


 
• Use mild cleaning components, which will help you preserve the bathtub for a long time and will also help you remove surface-level scratches.


 
• Do not use strong solutions such as concentrated bleach to remove stains. Instead, mix water and diluted bleach with a ratio of 10:2, respectively. Apply it to the tub's surface and leave it for 15-20 minutes to remove any surface-level stains.


 
• Always check the floor drain. You may unclog it using any small sticks or a small vacuum to suck out all the debris.


 
• Check the heater or faucet immediately if you smell rust or grease in the water. Rust in the water may stain or damage the bathtub in the long run.


 
• If you want to sand the bathtub, try using 400 grit sandpaper or 600 grit sandpaper for a more refined finish.

 

https://www.magnushomeproducts.com/blogs/inspired-living/how-to-install-a-freestanding-bathtub-a-diy-method-with-6-steps

 

I'm very curious about Tools You Need to Install a New Bathtub and I'm hoping you enjoyed the piece. Sharing is nice. Who knows, you might be helping someone out. I recognize the value of reading our article about How to Install a Bathtub.

Get it fixed!